That should be under 4 mils but I could have applied the other two coats thicker. more on the differences between the two here. The paint isn't gummy, or soft, once cured. Titan Capspray 115 6 Stage HVLP Turbine Paint Sprayer, choosing a selection results in a full page refresh, press the space key then arrow keys to make a selection. Im not confident that it was tinted to spec and is actually causing the issue. Having worked with this product many times, I suspect the paint rubbing off like that is more than likely a result of exposing the fresh paint to water, or the wrong primer was used. I settled on Sherwin-Williams Emerald Urethane Trim Enamel. It dries a little rougher than I would have liked, but nothing a little 400 grit couldn't take care of. 0000008187 00000 n Is it OK to use the aerosol version of the BIN shellac? Is there a difference in the way they clean once finished? Our site has everything you need to know about paintings, from the history of each type of painting, to the different styles and techniques used. I did 2 coats of SW Extreme Bond latex primer & 2 coats with the SW Emerald Urethane on raw doors. Answer: You didn't mention if you painted the cabinets with two coats or only one coat. "8_3074457345618274188productAdded", Returned items must be in the original packaging. I used an inexpensive HVLP sprayer from Wagner to apply the paint. cracknpop, thanks for the quick response. Thanks for the original post. It's a highly durable modified waterborne. 0000005139 00000 n Emerald Family - Sherwin-Williams Answer: Yes, I think the price sounds fair. If you're applying a second of primer you can just caulk in between coats. Though I haven't done a lot of spraying SW in general, but I have sprayed a fair amount of the ProClassic Acrylic and i have to thin well in excess of recommendations. Also, slightly of subject but when you are doing jobs, do you spray the inside of the cabinets and the shelving for these projects? YEARS WITH (480) 900-4020. Question: Are you sanding between paint coats? The pin hole texturing is from laying it on too thin. Matt G. (author) from United States on July 09, 2020: I would recommend Emerald urethane enamel over Super Paint. Answer: You can, but my local Sherwin Williams store advised against it when I was going to do glazing on one of my cabinet projects because they were unsure about the compatibility between Emerald urethane and the top coats of their Faux Impressions glaze and poly. The water base makes it dry fast, the alkyd base makes it level out, and the Urethane base makes it dry harder. Below you will find some of our favorite outfits for spraying Emerald urethane. Your session is about to timeout due to inactivity. You're also going to need multiple cans. All three can be used with BIN. Did you paint the inside of the boxes? You only need to scuff sand. You're also cleaning the cabinets way too soon after painting them. dojo.topic.subscribe('DefiningAttributes_Resolved', addReqListsJS8_3074457345618274188.setCatEntryId); What do you think the issue is? You don't have to apply a clear coat, but you can. On the wood surfaces I'll do extreme block with the emerald latex. I've read complaints online by people saying the semi-gloss finish was dull, but in my experience, two coats of semi-gloss over two coats of BIN shellac primer was the perfect amount of gloss for cabinets. If it's just a cheap HVLP gun from Harbor Freight, you're gonna have a bad time. Answer: No, but temperature plays a role in the finish and dry time. Appreciate your help so very much! If you sand in between coats of paint, make sure you're using a fine-grit otherwise you'll leave scratch marks in the paint very easily. | phone}}{{storeData.phone | phone}}. Although we did a good job cleaning the cabs, there are always going to be small areas with gunk that will bleed through, and the water based primer was terrible in this regard.
Chicken And Bacon Risotto Jamie Oliver,
Is Nick Digilio Still On The Radio,
Dylan Justice Sissons Age,
Johanna Parker Carnival Cottage,
Articles S